2360809566E – 6R1-PM-12.7-460-120-W-US-Lead
The 6-inch permanent magnet motor is engineered for high performance, simple startup and incredible long-term cost savings. Based on field trial data, owners and operators benefit from electrical cost savings as a result of 90% efficiency rating in the motor for an investment payback of less than two years in typical duty rate applications. Each MagForce High Efficiency System is powered with a permanent magnet motor that operates at a fraction of the energy consumption when compared to traditional induction systems. Plus, each 6-inch permanent magnet motor is paired with an innovative Franklin Electric engineered drive for intuitive startup and reliable protection for submersible pumping applications.
| Item: | 2360809566E |
| Model: | 6R1-PM-12.7-460-120-W-US-Lead |
| Type | Sand Fighter |
Ratings |
|
| HP 120Hz | 7.5-15 hp |
| Frequency | 120 Hz |
| Phases | Three-Phase |
| Amps - Full Load | 17.2 A |
| Amps - Service Factor | 20.5 A |
| Volts | 460 VAC |
| Voltage Tolerance (%) | -10.0% / +10.0% |
| Wire | 3-Wire |
| Thrust Bearing Rating | 3500 lb |
| Lead Length | 13 ft |
| Motor | Encapsulated |
| Continuous Duty | Yes |
| Efficiency Service Factor Load [%] | 92.00 % |
| Protection [IP] | IP68 |
| Lead Wire Size | AWG #10 |
| Lead Retainer Method | Lead Jam Nut |
| Motor Insulation Classification | F |
| Poles | 4 |
| Service Factor - 120Hz | 1.15 |
| VFD Required | YES |
Operation |
|
| Motor NEMA Frame Type | 6" |
| Motor Cooling | Water |
| Minimum Cooling Flow | .50 ft/sec |
| Motor Ambient Temperature Rating Nominal | 30 °C |
| Thrust Bearing Rating | 3500 lb |
| Motor Adapter | Double flange |
| Rotation | Counter clockwise facing the shaft |
| SubTrol Heat Sensor | No |
| Winding Resistance (Main Winding) | 0.86 |
| Maximum Starts in a 1 Hour Period | 20 |
| Maximum Immersion Depth | 350 m |
Materials of Construction |
|
| Motor Shaft End - Material | Stainless Steel 1.4462 |
| Thrust Bearing | Kingsbury Type |
| Seal | Mechanical Seal |
| Lead Insulation Material | EPR |
| Diaphragm Material | Ethylene-Propylene-Diene (EPDM) |
| Motor Bottom End Bell Material | Cast Iron with E-Coat Paint |
| Motor Fill Solution (Water Soluble / Non Toxic) | Yes |
| Motor Fill Solution | FES91 |
| Motor Top End Bell Material | Cast Iron with E-Coat Paint |
| Shaft Slinger Material | Nitrile Rubber (NBR) |
| Stator Ends Material | Carbon Steel |
| Stator Fill | Resin |
| Stator/ Motor Shell Material | 304SS |
| Winding Material | Copper |
Dimensions |
|
| Motor Diameter - Physical Diameter | 5.44" |
| Motor Length | 635 mm |
| Product Weight | 95 lb |
| Product Weight with Pack | 99 lb |
| Carton Length | 1070 mm |
| Carton Width | 155 mm |
| Carton Height | 212 mm |
| Shaft Diameter | 25 mm |
| Shaft End | Spline |
Other |
|
| Minimum Order Quantity | 1 |
| Drinking Water Agency Approvals | ANSI/NSF Standard 61 |
| Electrical Agency Approvals | UL |
| Warranty Standard Time | 12 Month Install / 24 Month Manufacturing |
| Repair Kit Available | Yes |
